News

Golding Official No. 3 for sale

This is a beautiful fully restored Golding Official No. 3 (5 x 8) tabletop press.  Don’t be fooled by chase size alone.  This press is so well engineered, that it can outperform a 6 x 10 Kelsey.  It is mounted to a period stand that works very well for operating the press.  It is a perfect press for the beginner or as a second press for the seasoned professional.  Easily can be carried to any room in your house or apartment.  The press has new rollers and trucks and prints as it did when new.  I will not ship presses.  It is too risky as shippers are not concerned as to what is inside even the best packaging.  You must come to my shop in the rural town of Lyme, CT.  It has easy access off route 95.  You will get a printing lesson on the press and have everything explained to your full satisfaction.  My custom Falstrom gauge is included with every press purchase.  The Falstrom gauge helps you adjust your press for proper inking and impression.  This press is sold and living in Delaware   Contact me at john.falstrom@att.net

Official No. 3 on its stand

Official No. 3 on its stand

Official No. 3

Official No. 3

Rare Golding Pearl for sale

This is a extremely rare opportunity.  It is not likely that you will see one like this again.   This is a fully restored Golding Pearl No. 1 (5 x 8) with the shipping crate it came in being used as the base.  This beautiful option was available from Golding but is seldom seen.   The famous Golding Pearls are some of the most sought after presses available today.   Ordinary examples are getting increasingly difficult to find.  Examples this unusual in this condition few and far between.  The press will be perfectly adjusted and come with my Falstrom gauge and an introductory lesson on the press.  It will also have new trucks and rollers which are not on the press as yet.  Shipping is not available.  You must come to my shop for pickup in rural Lyme, CT.  I am 10 minutes from Route 95.   A 10% deposit is required with the balance due on pickup.    This press is sold. 

I have other Golding presses available if this is not your preference.  Contact me:  john.falstrom@att.net

Golding Pearl No. 8 floor press (5 x 8):  $2395.00 Golding Official No. 3 tabletop (5 x 8):  Sold

See ad below

 

 Click here to go to the page to pay deposit.  Scroll down to end of pictures and add to cart.

img_0822 img_0821 img_0824 img_0831 img_0827 img_0826 img_0833 img_0823 img_0825 img_0828 img_0829 img_0832 img_0830 pearledit  

My visit to the old Golding factory 7/24/13

I had a very interesting adventure recently.  I went to the old Golding manufacturing building in Franklin, Massachusetts located about an hour and 45 minutes from my home.  This was the location they moved to from the Fort Hill section of Boston to gain more space in 1906.  The building was the former Snow, Bassett Co. Straw Goods plant.  It was an easy drive via route 6 through Rhode Island from my home in Lyme, CT.  Driving on route 6 which is a really old road lined in some spots with failed or failing businesses got me in the right frame of mind for what I would find at my destination.  As I pulled into the factory parking lot and looked at the large wood building in front of me, I could just imagine what it must have been like in Golding’s day.  The massive smoke stack sending heavy smoke into the air from the casting process going on inside, to the hustle and bustle of loading the heavy presses at the loading docks.  What a difference 100 years make.   All was quiet this day.  There were only a few cars in the parking lot, and as I walked inside I saw no people let alone a receptionist near the entry.  I started walking up the stairs to see if I could find someone to talk to and could really feel the ghosts of the former businesses that occupied the building.  The ceilings were tall and the creaking wood stairs were wide and lined with wainscoting that had been painted white too many times.   I went up to the second floor but found no one, so  I went up another floor.  Still no one.   One more floor and I saw someone behind a closed door that appeared to be a renter.  He paid no attention to me so rather than disturb him, I decided to go back downstairs and try a different approach.  Once on the first floor again, I heard voices and found a hall that lead into what I would say was the manufacturing area.  I say this because it was a large, high ceiling industrial looking area that was dark, wet, and dirty.  There I found two electricians working and asked where Kensol-Franklin was located.  Kensol was the current building owner I was looking for.   They make hot stamping presses used for applying foil to plastic items.  I was directed up a back stair which one flight up opened into a nicer work area that was loaded with metal working machines.  Out from a nearby office area came Paul, the gentlemen I had contacted.  We exchanged pleasantries and then he lead me to a massive work bench to show me what we had talked about on the phone.  It was a Golding Official No. 6 tabletop press in really nice condition.  All of its parts were present, and it was on it’s original wooden board.  Then, after I had admired it for a few minutes he ushered me across the room to another area and there on a dolly was another identical press.   They are impressive tabletops with a chase size of 8-1/4 x 12-1/2 which is larger than the first Jobber in the line.   Surprisingly, they are not the largest Golding made, but, I personally have never seen the largest model an Official No. 7 (10 x  15).   Paul told me that their business had slowed to the point that they had sold the building and were in the process of cleaning out when these two presses were rediscovered.   He then brought me into his office and showed me two printing plates.  goldingcatalogThe first one was a copper on wood halftone of an Official press.  It was an image I had seen before and matches the image used in the 1908 Golding catalog and maybe some other years as well.   The second one was an 11 pt brass plate of a Barnhart Brothers and Spindler ad for Golding equipment.  It looked familiar as well, but, I am not sure where I may have seen it prior.  It may have been in a copy of Inland Printer or an old printing machinery book which I read often.  It does have a date on it of May 1st 1917.   He also showed me some Golding cast iron case pulls that he had removed from a cabinet before it was discarded.   After a  little back and forth, we agreed on a price for the two presses, two plates, and 20 pulls.  What a strange feeling.  On July 24th 2013 I became the last customer to purchase a Golding press from the Golding factory.  Yes, I did it almost 100 years after Golding ceased to exist, but, these two presses were manufactured in the same building, paid for in the same building, and loaded at the same loading docks as used by Golding and his employees when they were in business.   In all likelihood, these two presses never left the premises.  I further believe that at least one of them was being used as it was found complete with dried up rollers, packing, and tympan still on the press according to Paul.  I cannot be sure which press company may have used it however.  There were several that occupied the building after Golding.  ATF purchased Golding in 1918 and continued to make the presses for about nine more years.  Thomson National Company made the famous Colts Armory press there after that.  And Kensol was part of the group that later owned Thomson.  The plates were definitely from the Golding era, the presses more likely from the ATF time period.  Neither press has the recurrent serial number faithfully applied by Golding on the top of the bed.  That suggests to me they might have been  ATF produced presses.    As a Golding enthusiast, this was a pretty special day and I feel very fortunate to have had the experienced.  Contact:  john.falstrom@att.net

Official No. 6's

The Golding Pearl No. 2

Not too long ago I had the good fortune of purchasing a Pearl tabletop in Vermont.  Pearl No. 2 When I first saw it in a picture seen at right, I thought I was looking at a Pearl No. 3 in tabletop form which was really exciting as they are few and far between.  The first thing that surprised me when I first saw the press in person was the feed table.  When looking at the picture I thought that the feed board was just sitting in front of the press and not attached.  It actually is attached to the press with the original brackets, but, in a position I was not expecting down below the platen.  I have not seen any other Golding tabletop with a feed board, let alone one that is mounted in this unusual position.  The second surprise was even bigger.  After my wife and I drove to Vermont and picked it up, it began to nag at me that the press seemed too small.  I went out to the parking lot where the car was parked for the night to actually measure the chase and my suspicion was confirmed as the chase measured 6 x 9 rather than 7 x 11.  It began to sink in that without knowing it initially, I had just purchased a Pearl No. 2, and to my knowledge, this was the only known example of that model.  It was pretty exciting to say the least.  I have since restored it and it is now my most favored press.   Within just a couple of months, a good friend, (Tim Dunn of Moonstruck Press) sent me a picture of a press he picked up when he purchased a letterpress shop.  It was another Pearl No. 2!   Then a couple of weeks later, another friend alerted me to a press on auction that was yet another Pearl No. 2.  Well…I was successful in that auction and drove 16 hours to retrieve what is now the third Pearl No. 2 that has surfaced.  This third one, and Tim’s second one were in need of some love.  Tim and I collaborated on our Potter restorations in the past and now here we were again both restoring the same press.    This model was never available in treadle form like the No. 1 and No. 3.  It just came as a tabletop as seen in the photos.  It apparently never became as popular as it’s smaller and larger sisters.  I don’t know why because it is a wonderful size and working press.  We figure the manufacturing date to be around 1875.  It can’t be too much earlier or later because of the design and known history of the Pearl press.  As Steve O. Saxe wrote in his “A brief history of Golding & Co.” this is most likely the second hand press that George T Dunlap purchased in 1884.  He wrote that this was his favorite and the best press he ever owned.  This is the same Dunlap of the famed publishing firm Grosset and Dunlap.  The following is a pictorial of the third presses restoration process.  The only thing left to do and not shown on the finished press as of this writing is to get the feed board brackets and feed board done.  I am having new brackets cast for both this press and Tim’s using a bracket from the first press that still had them intact.  An interesting note about the rails on this model is that they are greater than .918 high.  It requires careful measurements to determine the roller diameter which needs to be greater than the truck diameter.  If you make the rollers the same size as the trucks on this press, they would not ink the form.  The metal repairs were done by a local machinist.  He is available to do work if you have a press that is need of repair.  I recommend him highly.  Contact me at john.falstrom@att.net for his contact information.

 

 

First Pearl No. 2 Auction photo 1 Finished press Finished press Broken roller arm 2 Broken roller hook arm close up Brazing repair Body putty fill Painted repair Roller hook arm brazing repair Body putty fill Painted repair  

 

 

Pearl No. 3

 

This restored Golding Pearl No. 3 was picked up on July 10, 2013 and will live in South Attleboro, Ma.

 

Pearl

Official No. 4

IMG_0254 

 

This restored Golding Official No. 4 was picked up on June 14, 2013 and will be living in NYC.

Golding Official No. 4 letterpress for sale

I have just acquired a nice 6 x 9 tabletop press that is ready for restoration and subsequent sale.  If you are not familiar with the Golding Official line, they are of the highest quality presses available and the 6 x 9 is the most desirable size.  This one is unique as it is from the last 100 presses produced by Golding in 1919.  It will be carefully restored, adjusted and tested to print as intended when new.   It will have new rollers and trucks made to original specifications.  It will include the press, my custom Falstrom roller/platen adjusting gauge, an introductory lesson on the press that includes pulling some prints, care and maintenance, and all your questions answered.   As with all my restorations, I do not ship.  Shippers are too rough and breakage is likely.  You must come to my shop in Lyme, CT.    If interested please contact john.falstrom@att.net  A deposit will be taken with the balance due on pick up.  This press is sold.

1902 Golding Improved Pearl No. 11 for sale.

This is my latest restoration.  It will be properly adjusted and ready to print.   It will get new trucks, cores and rollers when a deposit is taken.  It will have the cubby door reproduced by a finish carpenter and be installed at the same time.  Pearls are great presses suitable for the beginner or experienced alike.  It’s easy running and a pleasure to treadle.  They have a chase size of 7 x 11, three rollers for better inking, and the indispensable throw off lever.  It comes with my custom roller/platen gauge for easier adjustment of inking and impression.  It includes an introduction to letterpress lesson at my shop.  I will personally load it into your vehicle.  As with all my press sales, there is no shipping.  You must come to pick it up at my shop in rural Lyme, CT.   You will print on your press and be satisfied that the press works properly and all you questions have been carefully answered before the loading process begins.  That’s the way I like to do business.  Pearls are getting harder to find.  Don’t miss this opportunity.  Sold and will live in Atlanta, thanks!

  Pearl front Pearl right side Pearl rear Pearl left side

You can reserve this press for your own by providing the deposit listed here and pay using Paypal or contacting me and sending a check.  Balance is due on pickup.  Press must be picked up in a timely manner.  john.falstrom@att.net

  

 

 

 

Potter Proof Press

This is my latest project.  A Hacker/Potter proof press No. 3.  I would date it at about 1913-15 or so.  It’s serial No. 1374 which suggests it is in that range.  The first Potters were patented in 1910 and an ad boasted the company had sold over 1000 units by 1912.  If it had its original nameplate it would have helped date it, but, sadly it was missing.  Early nameplates list Wanner as the maker.  I am fortunate to have a partner doing the exact same press in Tim Dunn.  Together, we hope to bring both of these presses back to their former glory.  We purchased them from John Barrett, a great source for all things letterpress related.  The press was about as dirty as I have ever tackled.  Inkcicles were up to 12″ long before they were broken while moving the press.

  

 

For more pictures and discussion of the project click here:

 

 

Cook’s Victor (6″x9″) tabletop letterpress for sale

I have just completed restoration on another Cook’s Victor. I normally stay with Golding, but, this make and model is something special.  It dates from the late 1800’s and the quality is impressive. It works on the same engineering principal as the Pilot, but, in my opinion is actually better built.  The spring system for rollers to apply pressure to the form is excellent and the rails are thicker than any press I have ever seen.  Thicker rails means the press will wear less than one with tiny rails.  In their day Victors became such competition to Kelsey, that he purchased Cook’s company and soon discontinued making the press in favor of his own less expensive models. That’s one way to beat the competition! As with all my press sales, there is no shipping. You must come to my shop to pick up the press. My shop is 10 minutes off route 95 in a beautiful rural town.(Lyme, CT.) When you come, you will get a free letterpress introductory lesson and print on your new press. You can stay as long as needed to feel comfortable. Also included is my proprietary combination roller/platen adjusting gauge. The gauge helps simplify two adjustments beginners often find challenging, inking and impression. The press includes new rollers which have not been purchased as yet.  I have made the new cores and trucks seen in one of the pictures. Get started right, with a beautiful high quality press that has been properly restored and adjusted. One that you will print on before taking it home. The handle on this press is reversable so righty or lefty can be happy. The finish on the press is a three step paint process that has a nice soft look much like it would have had originally. If you are looking for a tabletop press come take a look. This is a high end press capable of producing a wide variety of printed products.  contact: john.falstrom@att.net  Sold and living in St Louis. 4/16/2012

  100_4040 100_4041 100_4042 100_4043 100_4044 100_4045  

 

Cards by name

Solution Graphics